McGillivray, Don [IT]
Donald.A.McGillivray at sprint.com
Fri Sep 28 11:31:35 CDT 2007
Max, The way I did it was to establish a position on the page, bar width, and a maximum bar height for the rectangles. If you have only two values to compare (walked v target) just make the rectangle representing the target the maximum size and whatever color you want it. Then you can superimpose a rectangle of a different color over the target, and set its height value according to the ratio of walked to target. Just apply the same ratio to the max height, set that as the height value, and redraw. Note that the properties sheet expresses the rectangle's dimensions in inches, but your code must use twips. 1 inch = 1440 twips, if my memory serves. I've also done this by positioning different sized rectangles next to each other when I had more than two metrics to compare to the whole. Hope this helps . . . Don -----Original Message----- From: accessd-bounces at databaseadvisors.com [mailto:accessd-bounces at databaseadvisors.com] On Behalf Of max.wanadoo at gmail.com Sent: Friday, September 28, 2007 9:00 AM To: 'Access Developers discussion and problem solving' Subject: Re: [AccessD] FW: FW: Create a BarGram from data I have never done this Don, Can you Scale a range so that it, say, fits a given size and then, say, colour the increasing element, say blue, and the bit still to go, say red? It would be a start. Thanks Max -----Original Message----- From: accessd-bounces at databaseadvisors.com [mailto:accessd-bounces at databaseadvisors.com] On Behalf Of McGillivray, Don [IT] Sent: Friday, September 28, 2007 4:51 PM To: Access Developers discussion and problem solving Subject: Re: [AccessD] FW: FW: Create a BarGram from data Max, Well, you probably already have this part figured out, but it's the only part I have an idea about. I've created "bar charts" on Access reports and forms using retrieved values to describe the dimensions of rectangle controls. But I suspect that your question is aimed more at creating the graphic externally using Access data and moving it into your website, presumably in an automated way. That's beyond my ken, for sure. I've never used Access pages, but maybe there's some potential there? Good luck . . . Don -----Original Message----- From: accessd-bounces at databaseadvisors.com [mailto:accessd-bounces at databaseadvisors.com] On Behalf Of max.wanadoo at gmail.com Sent: Friday, September 28, 2007 8:33 AM To: 'Access Developers discussion and problem solving' Subject: [AccessD] FW: FW: Create a BarGram from data Sorry for the repeat posting, but I have to try one more time to see if anybody can help me with this. Thanks Max -----Original Message----- From: accessd-bounces at databaseadvisors.com [mailto:accessd-bounces at databaseadvisors.com] On Behalf Of max.wanadoo at gmail.com Sent: Friday, September 28, 2007 1:51 PM To: 'Access Developers discussion and problem solving' Subject: [AccessD] FW: Create a BarGram from data Hi folks, just re-posting this hoping that somebody will be able to help me out here. Ta Max -----Original Message----- From: accessd-bounces at databaseadvisors.com [mailto:accessd-bounces at databaseadvisors.com] On Behalf Of max.wanadoo at gmail.com Sent: Friday, September 28, 2007 6:38 AM To: 'Access Developers discussion and problem solving' Subject: [AccessD] Create a BarGram from data Hi Folks, I have to do something which I have never done before and would really appreciate your help and feedback. The charity I support is doing a charity walk and we need to have a guage generated showing progress (something like you see on the side of a church to show how the restoration fund for the new church roof is progressing). My Access tables will capture the MilesWalked v MilesTarget and FundsRaised v FundsTarget. Somehow I have to generate a "picture" of each from these values which I can then drop onto the web site as two graphics. I will need to "scale" the MilesWalked to the MilesTarget and create the "picture" from that. And then do the same with the funds. A sort of Progress Bar thingie but for the web site. All input is captured into an MDB, but how on earth do I do the rest? Any help would be most appreciated. Evan a start point. Thanks Max -- AccessD mailing list AccessD at databaseadvisors.com http://databaseadvisors.com/mailman/listinfo/accessd Website: http://www.databaseadvisors.com -- AccessD mailing list AccessD at databaseadvisors.com http://databaseadvisors.com/mailman/listinfo/accessd Website: http://www.databaseadvisors.com -- AccessD mailing list AccessD at databaseadvisors.com http://databaseadvisors.com/mailman/listinfo/accessd Website: http://www.databaseadvisors.com -- AccessD mailing list AccessD at databaseadvisors.com http://databaseadvisors.com/mailman/listinfo/accessd Website: http://www.databaseadvisors.com -- AccessD mailing list AccessD at databaseadvisors.com http://databaseadvisors.com/mailman/listinfo/accessd Website: http://www.databaseadvisors.com