[AccessD] OT - Home networking question

Doug Murphy dw-murphy at cox.net
Mon Apr 11 21:39:31 CDT 2011


Thanks all. A few of your suggested tweaks and all is good.

-----Original Message-----
From: accessd-bounces at databaseadvisors.com
[mailto:accessd-bounces at databaseadvisors.com] On Behalf Of Jim Lawrence
Sent: Monday, April 11, 2011 1:02 PM
To: 'Access Developers discussion and problem solving'
Subject: Re: [AccessD] OT - Home networking question

PS: Always save your router setting after the changes have been perfected.
So if anything blows up it will only take you minutes instead of days to
recover.

Jim

-----Original Message-----
From: accessd-bounces at databaseadvisors.com
[mailto:accessd-bounces at databaseadvisors.com] On Behalf Of jwcolby
Sent: Monday, April 11, 2011 12:15 PM
To: Access Developers discussion and problem solving
Subject: Re: [AccessD] OT - Home networking question

And set the router interface page to a new address.  Typically the router
answers up on 192.168.0.1. 
  Obviously if you have two of these things, the second has to answer up
somewhere else - I usually do 192.168.0.2, 192.168.0.3 etc.

In order to set that part, you have to plug the router directly into a
disconnected laptop or pc. 
That allows the disconnected computer to "talk to" 192.168.0.1 on the
"second" or alternate router long enough to tell that router to answer up on
an alternate address.

And then never do a factory reset... or you will have to do this all over.

John W. Colby
www.ColbyConsulting.com

On 4/11/2011 2:45 PM, Jim Dettman wrote:
> Doug,
>
>    No need to replace the three routers; use can use them as a hub.  
> The trick is to disable the DNS in reach, set RIP to none, and then 
> when you connect to the one router after the cable modem, plug the 
> cable into the
LAN
> port (not the WAN port as it is now).
>
>    This also effectively turns a Wireless Router into a simple 
> Wireless Access point.
>
> Jim.
>
> -----Original Message-----
> From: accessd-bounces at databaseadvisors.com
> [mailto:accessd-bounces at databaseadvisors.com] On Behalf Of Doug Murphy
> Sent: Monday, April 11, 2011 12:52 PM
> To: 'Access Developers discussion and problem solving'
> Subject: Re: [AccessD] OT - Home networking question
>
> Thank you Stuart, Drew and Jim,
>
> You all had similar suggestions which is probably the way the network
should
> have been done from the start. I am going to remove the first Ethernet 
> hub and go directly into the first router. We will then branch out from
there.
> The reason for this mess in the first place was that I only had one 
> cable
to
> my office and several computers there to network together. What I am 
> thinking would be the cleanest approach now would be to put the 
> Ethernet
hub
> in my office and let the router attached to the cable modem assign all 
> our network IP addresses. Would that work?
>
> Thanks again. It is really great to have access to so much knowledge 
> 24/7
>
> Doug
>
> -----Original Message-----
> From: accessd-bounces at databaseadvisors.com
> [mailto:accessd-bounces at databaseadvisors.com] On Behalf Of Stuart
McLachlan
> Sent: Sunday, April 10, 2011 3:47 PM
> To: Access Developers discussion and problem solving
> Subject: Re: [AccessD] OT - Home networking question
>
> Are you sure that your terminology if correct?
>
> It would make more sense if you has one router attached to your cable
modem
> and hubs/switches connected to that router from  the three locations.
>
> Can you give us the make/model numbers of  these devices?
>
> --
> Stuart
>
>
> On 10 Apr 2011 at 10:39, Doug Murphy wrote:
>
>> Folks,
>>
>> I know there are several members of this group who are knowledgeable 
>> about computer networking. We have a network in our home/offices that 
>> has evolved over time. The basic configuration is that out of our 
>> cable modem there is an Ethernet hub. 3 cables come out of this hub 
>> and go to routers, one in my office in one part of the house, one in 
>> my wife's office, and one to our wifi. These have been added as 
>> requirements came about so this probably isn't the best configuration.
>> At the present we don't use the network to access machines in other 
>> parts of the system. I have several in my office that access each 
>> other, but they are on the same router.  I do want to stay with the 
>> wired systems to the offices.  We just added a home security system 
>> that can be monitored over the network. It is connected to my router 
>> as it is closest to the box. I can access the system by typing in 
>> it's IP address. Now I am trying to access it from other points in 
>> the network and the IP is not visible. As you can probably tell I am 
>> network challenged. I think what I need to do is find the IP address 
>> of the security system from outside my router. How can this be done?
>>
>> Thanks
>>
>> Doug
>>
>>
>>
>> --
>> AccessD mailing list
>> AccessD at databaseadvisors.com
>> http://databaseadvisors.com/mailman/listinfo/accessd
>> Website: http://www.databaseadvisors.com
>>
>
>
>
--
AccessD mailing list
AccessD at databaseadvisors.com
http://databaseadvisors.com/mailman/listinfo/accessd
Website: http://www.databaseadvisors.com

--
AccessD mailing list
AccessD at databaseadvisors.com
http://databaseadvisors.com/mailman/listinfo/accessd
Website: http://www.databaseadvisors.com




More information about the AccessD mailing list