[AccessD] A2K7 Navigation Pane

A.D.:

I put in just the two lines:

    DoCmd.SelectObject acForm, , True
    DoCmd.RunCommand acCmdWindowHide

to turn it off and sent it over to the client.  Worked perfectly.  So we'll
add it to the local options form so each user can decide whether they want
the Nav pane on or off.  

Thanks and regards,

Rocky





 	
	

-----Original Message-----
From: accessd-bounces at databaseadvisors.com
[mailto:accessd-bounces at databaseadvisors.com] On Behalf Of A.D.TEJPAL
Sent: Monday, November 26, 2007 10:53 PM
To: Access Developers discussion and problem solving
Subject: Re: [AccessD] A2K7 Navigation Pane

Rocky,

    No need to put it on every form. It is for you to decide as to which
form is most convenient for carrying out this action. Typically, the
switchboard form (which is usually the start up form) could be considered
for such role.

Best wishes,
A.D.Tejpal
------------

  ----- Original Message -----
  From: Rocky Smolin at Beach Access Software
  To: 'Access Developers discussion and problem solving' 
  Sent: Monday, November 26, 2007 21:39
  Subject: Re: [AccessD] A2K7 Navigation Pane


  A.D.:

  Does the code:

      DoCmd.SelectObject acForm, , True
      DoCmd.RunCommand acCmdWindowHide

  have to appear in each form, or just called once from the opening form?

  Thanks and regards,

  Rocky  


  -----Original Message-----
  From: accessd-bounces at databaseadvisors.com
  [mailto:accessd-bounces at databaseadvisors.com] On Behalf Of A.D.TEJPAL
  Sent: Tuesday, November 20, 2007 9:26 PM
  To: Access Developers discussion and problem solving
  Cc: A.D.TEJPAL
  Subject: Re: [AccessD] A2K7 Navigation Pane

  Rocky,

      A convenient arrangement would be to have two command buttons named
  CmdHide and CmdShow on a form so as to hide or show the NavPane window in
  Access 2007. If the user is in a position to ensure that forms group in
  NavPane is never put in collapsed state, the code applicable in Access 2K
&
  2K3, as given below, would work in A2K7 as well.

  Code in form's module - A2K7
  (Forms group in NavPane must not be in collapsed state)
  ========================================
  Private Sub CmdHide_Click()    
      ' Make NavPane the active window and hide it
      DoCmd.SelectObject acForm, , True
      DoCmd.RunCommand acCmdWindowHide
  End Sub
  '-------------------------------------------------------

  Private Sub CmdShow_Click()
      DoCmd.SelectObject acForm, , True
  End Sub
  ========================================

      The simple solution given above will not work if the forms group in
  NavPane window is in collapsed state. This is because hiding the NavPane
can
  get implemented only if the focus stays on NavPane window during execution
  of acCmdWindowHide command. However when an attempt is made in Access 2007
  to activate the NavPane via DoCmd.SelectObject method while the pertinent
  object group is in collapsed state, the focus reverts back to the active
  form. This results in acCmdWindowHide command taking effect on the form
  itself instead of the intended target (NavPane). Thus you land up with
  hiding the form itself, instead of the NavPane.

      Remedy lies in hiding all active forms and reports prior to hiding the
  NavPane, and thereafter, un-hiding the forms & reports. Of course no other
  object like table or query should be in open state.

      It is observed that it is not necessary to select any specific object
in
  NavPane. This argument in DoCmd.SelectObject statement can be left blank
  Mere selection of a type group (acForm, acTable etc) is adequate. If the
  group mentioned in DoCmd.SelectObject method does not yet have any object,
  it will not force that group's title bar to show up in the NavPane if not
  already visible (otherwise it will). This however does not detract from
  effectiveness of proposed approach and even such an empty group serves
  satisfactorily as an argument to DoCmd.SelectObject method.

      Sample code in form's module, as given below, will ensure effective
  hiding / un-hiding of NavPane window under all situations, even if all
  object groups in NavPane are in collapsed state. Although this code is
meant
  for Access 2007, it can be used in Access 2003 as well (statements meant
for
  hiding / un-hiding of active forms / reports are however not needed in
  Access 2003).

      It permits unrestricted number of forms / reports to stay in open
state.
  It is also ensured that while cycling through forms/reports for bulk
hiding/
  unhiding, any forms kept deliberately hidden to start with, continue in
this
  state while other temporarily hidden objects are made visible again.

  Best wishes,
  A.D.Tejpal
  ------------
--
AccessD mailing list
AccessD at databaseadvisors.com
http://databaseadvisors.com/mailman/listinfo/accessd
Website: http://www.databaseadvisors.com

No virus found in this incoming message.
Checked by AVG Free Edition. 
Version: 7.5.503 / Virus Database: 269.16.8/1153 - Release Date: 11/26/2007
9:08 PM