Tydda Jon - Slough
jon.tydda at lonza.com
Wed Dec 30 02:58:26 CST 2009
Try pressing the button, and setting it to normal. That should solve the problem. Jon -----Original Message----- From: dba-tech-bounces at databaseadvisors.com [mailto:dba-tech-bounces at databaseadvisors.com] On Behalf Of Rocky Smolin Sent: Wednesday, December 30, 2009 1:25 AM To: 'Discussion of Hardware and Software issues' Subject: Re: [dba-Tech] Hub problem No crossover but one of the post is labeled Link with a button next to it normal/uplink. It's set to uplink. And that port is the one connected to the router. R -----Original Message----- From: dba-tech-bounces at databaseadvisors.com [mailto:dba-tech-bounces at databaseadvisors.com] On Behalf Of Stuart McLachlan Sent: Tuesday, December 29, 2009 3:27 PM To: Discussion of Hardware and Software issues Subject: Re: [dba-Tech] Hub problem If it's an old hub, the ports are probably not "auto-configuring". You may need a "cross-over cable" to connect the hub to the router (unless on of the ports on it is marked as a cross- over port - in which case, use that one to connect to the router).. -- Stuart On 29 Dec 2009 at 12:53, Rocky Smolin wrote: > Well, the sites describe my problem. And it's probably the hub because > everything that doesn't work through the hub works through the router. > Sounds like a switch might be a faster solve. > > R > > -----Original Message----- > From: dba-tech-bounces at databaseadvisors.com > [mailto:dba-tech-bounces at databaseadvisors.com] On Behalf Of Jon Tydda > Sent: Tuesday, December 29, 2009 12:22 PM > To: 'Discussion of Hardware and Software issues' > Subject: Re: [dba-Tech] Hub problem > > 169.254.x.x is an automatic configuration address - explained here: > http://ask-leo.com/why_cant_i_connect_with_a_169254xx_ip_address.html > > Another site > (http://www.pctechbytes.com/network/networkdetail.php?Fix-169.254.x.x-IP-Add > ress-Problem-4) suggests this: > > If the computer network was working then quit: > > 1. Release and renew the IP Address. Go to Start>Run and type cmd and hit > OK. At the prompt, type ipconfig /release and then reboot. You could just > type ipconfig /renew next, but rebooting is more thorough. > 2. If that doesn't work, release the IP again and shutdown. Next power cycle > the modem and router. > > A third site (http://www.chicagotech.net/troubleshootingipconfig.htm) says: > > Why do I get 169.254.x.x IP? > > Symptom: The Internet Assigned Numbers Authority (IANA) has reserved > 169.254.0.0-169.254.255.255 for Automatic Private IP Addressing. If the > computer can't get ip from DHCP, APIPA provides an address that is > guaranteed not to conflict with routable addresses. > > Resolutions: 1) Make sure you have good connection. > 2) Check the hardware and settings. > 3) Make sure the DHCP is working. > 4) For the test, you can assign static ip. If static ip works, it is > possible DHCP issue. If static ip doesn't work, check the hardware or > connection. > 5) WinSock2 stack may be corrupted and need to repair. > > Hope that's of some use! > > > Jon > > -----Original Message----- > From: dba-tech-bounces at databaseadvisors.com > [mailto:dba-tech-bounces at databaseadvisors.com] On Behalf Of Rocky Smolin > Sent: 29 December 2009 20:09 > To: 'Discussion of Hardware and Software issues' > Subject: Re: [dba-Tech] Hub problem > > /Release and /all didn't change anything. IPv4 address is still > 169.254.225.78. Should be something like 192.168.1.x. > > I did ipconfig /renew and got the message "An error occurred while renewing > interface Local Area Connection : unable to contact your DHCP server. > Request has timed out." > > R > > -----Original Message----- > From: dba-tech-bounces at databaseadvisors.com > [mailto:dba-tech-bounces at databaseadvisors.com] On Behalf Of Gary Kjos > Sent: Tuesday, December 29, 2009 10:57 AM > To: Discussion of Hardware and Software issues > Subject: Re: [dba-Tech] Hub problem > > Have a look here > > http://www.networkclue.com/os/Windows/commands/ipconfig.aspx > > You could try to do an ipconfig /all > > and then an ipconfig /release > > followed by another > > ipconfig /all > > on the workstation connected to the hub. > > You have to do Run and then cmd.exe to get a dos box to do ipconfig > > GK > On Tue, Dec 29, 2009 at 12:44 PM, Rocky Smolin <rockysmolin at bchacc.com> > wrote: > > Yeah, all the same workgroup. When I pull the wire from the hub and > > plug it into the router it works regardless of machine. ICS can't be > > enabled because I've only one network (so says the help dialog). > > > > R > > > > -----Original Message----- > > From: dba-tech-bounces at databaseadvisors.com > > [mailto:dba-tech-bounces at databaseadvisors.com] On Behalf Of Max > > Wanadoo > > Sent: Tuesday, December 29, 2009 8:57 AM > > To: 'Discussion of Hardware and Software issues' > > Subject: Re: [dba-Tech] Hub problem > > > > Are the WorkGroups the same, ie WORKGROUP or MSHOME etc? > > > > Also the pc with the internet access needs to have ICS enabled (search > > help for ICS Internet Connection Sharing) > > > > Max > > > > > > -----Original Message----- > > From: dba-tech-bounces at databaseadvisors.com > > [mailto:dba-tech-bounces at databaseadvisors.com] On Behalf Of Rocky > > Smolin > > Sent: 29 December 2009 16:27 > > To: List; 'Access Developers discussion and problem solving' > > Subject: [dba-Tech] Hub problem > > > > Dear List: > > > > I have a nice netgerar router with wireless and four ports. Problem > > is that I need five ports. I had an old hub in the cabinet so I > > connected one of the router's ports to the hub. One of the ports on > > the hub goes to a Netgear XE102 wall plugged bridge which gives > > another computer and the HDTV access to the network and the net > > through two other XE102s. Everything works a treat. > > > > But when I try to connect another machine (via regular Cat-5/RJ45 > > cable) to an empty port on the hub, the computer can see the network > > but not the internet - windows diagnosis shows the computer is > > connected to 'unidentified network', 'local access only', and says > > that the IP address is invalid - which it is - looks like some kind of > > fixed IP instead of the 192.168.1.n number assigned by the router (?). > > > > Oddly, the Netgear bridge doesn't have a problem - don't know why. And > > years ago I was using this hub to connect machines. So I think the hub > > is good (the Netgear Bridge works in all the hub's ports) and the > > cables are good - I tested them by using the router's ports - and it > worked. > > > > Anybody know why these ports won't work? Is there a way to use the > > empty ports on the hub? Should I get a switch? > > > > > > > > MTIA > > > > > > > > Rocky > > > > > > > > > > > > > > _______________________________________________ > > dba-Tech mailing list > > dba-Tech at databaseadvisors.com > > http://databaseadvisors.com/mailman/listinfo/dba-tech > > Website: http://www.databaseadvisors.com > > > > _______________________________________________ > > dba-Tech mailing list > > dba-Tech at databaseadvisors.com > > http://databaseadvisors.com/mailman/listinfo/dba-tech > > Website: http://www.databaseadvisors.com > > > > > > -- > Gary Kjos > garykjos at gmail.com > > _______________________________________________ > dba-Tech mailing list > dba-Tech at databaseadvisors.com > http://databaseadvisors.com/mailman/listinfo/dba-tech > Website: http://www.databaseadvisors.com > > > _______________________________________________ > dba-Tech mailing list > dba-Tech at databaseadvisors.com > http://databaseadvisors.com/mailman/listinfo/dba-tech > Website: http://www.databaseadvisors.com > > > _______________________________________________ > dba-Tech mailing list > dba-Tech at databaseadvisors.com > http://databaseadvisors.com/mailman/listinfo/dba-tech > Website: http://www.databaseadvisors.com > > > _______________________________________________ > dba-Tech mailing list > dba-Tech at databaseadvisors.com > http://databaseadvisors.com/mailman/listinfo/dba-tech > Website: http://www.databaseadvisors.com > _______________________________________________ dba-Tech mailing list dba-Tech at databaseadvisors.com http://databaseadvisors.com/mailman/listinfo/dba-tech Website: http://www.databaseadvisors.com _______________________________________________ dba-Tech mailing list dba-Tech at databaseadvisors.com http://databaseadvisors.com/mailman/listinfo/dba-tech Website: http://www.databaseadvisors.com This communication and its attachments, if any, may contain confidential and privileged information the use of which by other persons or entities than the intended recipient is prohibited. If you receive this transmission in error, please contact the sender immediately and delete the material from your system.