Rocky Smolin
rockysmolin at bchacc.com
Tue Jul 19 00:11:30 CDT 2011
Worth a shot. -----Original Message----- From: dba-tech-bounces at databaseadvisors.com [mailto:dba-tech-bounces at databaseadvisors.com] On Behalf Of Jim Lawrence Sent: Monday, July 18, 2011 8:11 PM To: 'Discussion of Hardware and Software issues' Subject: Re: [dba-Tech] Graphics controller problem Hi Rocky: If you have a video card built on the motherboard it may not adapt to another card being inserted it so you will most likely have to go into the BIOS and disable the default video card...seems that have ran into this problem a few times before. ;-) HTH Jim -----Original Message----- From: dba-tech-bounces at databaseadvisors.com [mailto:dba-tech-bounces at databaseadvisors.com] On Behalf Of Rocky Smolin Sent: Monday, July 18, 2011 5:01 PM To: 'Discussion of Hardware and Software issues' Subject: Re: [dba-Tech] Graphics controller problem There is one but it doesn't show on the device manager and when I plug one of the monitors into it, there's nothing on the screen, so I'm assuming it's disabled. Rocky -----Original Message----- From: dba-tech-bounces at databaseadvisors.com [mailto:dba-tech-bounces at databaseadvisors.com] On Behalf Of Bill Patten Sent: Monday, July 18, 2011 3:45 PM To: Discussion of Hardware and Software issues Subject: Re: [dba-Tech] Graphics controller problem Hi again, I doubt this will help either but any chance there is a built in video card on the PC that needs to be disabled? Bill -------------------------------------------------- From: "Rocky Smolin" <rockysmolin at bchacc.com> Sent: Monday, July 18, 2011 3:38 PM To: "List" <dba-tech at databaseadvisors.com>; "'Off Topic'" <dba-ot at databaseadvisors.com> Subject: [dba-Tech] Graphics controller problem Dear Lists: I moved a dual monitor graphics card - ATI Radeon XPRESS 200 Series - from my old XP machine to another machine running W7 Ultimate 32 bit where is will not operate correctly. Device manager says Code 12 This device cannot find enough free resources that it can use. If you want to use this device, you will need to disable one of the other devices on this system. (Code 12) Recommended resolution Two devices have been assigned the same I/O ports, the same interrupt, or the same Direct Memory Access channel (either by the BIOS, the operating system, or a combination of the two). This error message can also appear if the BIOS did not allocate enough resources to the device (for example, if a universal serial bus (USB) controller is not an interrupt from the BIOS because of a corrupted Multiprocessor System (MPS) table). You can use Device Manager to determine where the conflict is and disable the conflicting device. On the General Properties tab of the device, click Troubleshoot to start the Troubleshooting Wizard. Location is PCI bus 1, device 5, function 0. I can't find another device in conflict with this one. And there's no Troubleshoot command button on the General Properties tab. Any ideas on where to start to resolve this problem? Both monitors are plugged into the card - only one is operating. TIA Rocky _______________________________________________ dba-Tech mailing list dba-Tech at databaseadvisors.com http://databaseadvisors.com/mailman/listinfo/dba-tech Website: http://www.databaseadvisors.com _______________________________________________ dba-Tech mailing list dba-Tech at databaseadvisors.com http://databaseadvisors.com/mailman/listinfo/dba-tech Website: http://www.databaseadvisors.com _______________________________________________ dba-Tech mailing list dba-Tech at databaseadvisors.com http://databaseadvisors.com/mailman/listinfo/dba-tech Website: http://www.databaseadvisors.com _______________________________________________ dba-Tech mailing list dba-Tech at databaseadvisors.com http://databaseadvisors.com/mailman/listinfo/dba-tech Website: http://www.databaseadvisors.com